Welcome to Adamov Reglazing, your trusted partner for bathtub reglazing and cabinet refinishing services in Southern California. We proudly serve residential and commercial clients across multiple locations, helping you revitalize your bathrooms and kitchens with cost-effective, professional solutions.
Looking for bathtub reglazing in Hemet? Adamov Reglazing restores porcelain, cast iron, fiberglass, and acrylic tubs across Hemet and the San Jacinto Valley — ready to use in about 7 hours, backed by a 4-year warranty, with no hidden costs. Reglazing instead of replacing saves most homeowners thousands of dollars and days of demolition mess.
Hemet has a lot of homes from the 60s through the 80s, and many still have their original tubs — cast iron and porcelain that have gone dull, stained, or chipped after decades of use. Newer builds bring us fiberglass and acrylic units with scratches, spider cracks, and worn-out finishes. Either way, the fix is the same: we repair the damage, then spray a new factory-smooth finish in a single visit — a brand-new-looking tub for a fraction of replacement cost.
We handle:
We wrapped up an acrylic enclosure reglazing job over in Hemet not long ago, and this one was a little different from most. Usually people call us because something’s falling apart — stained, cracked, peeling, worn down to the point they can’t stand looking at it. This enclosure was actually in pretty good shape. The homeowner just wanted to give it a fresh, modern, bright look, and reglazing was the way to get there without ripping the whole thing out.
He had a clear plan going in, which always makes my job easier. He wanted all the fixtures off the wall before we touched the surface, because once we were done he was putting in all new ones anyway. So that’s where we started. We took off the showerhead, the handles, the trim, all of it, and set everything aside. Pulling the fixtures first gives you a clean, uninterrupted surface to work with, and it means the new coating goes on without any awkward edges or gaps around the hardware. When his new fixtures go back on later, everything sits flush against a fresh finish.
With the fixtures out of the way, we moved into the part that really makes or breaks a job like this — the cleaning. I did a deep clean across the entire surface, and I don’t cut corners on this. On a tub and shower combination refinishing job, there’s more than just the smooth panels to deal with. This enclosure had tile, and tile means grout lines, and grout lines collect grime you can’t always see. So I went around and brushed out every single line, working into the corners and along each tile, making sure there wasn’t any dirt or soap buildup left sitting between them. If you leave that behind, the coating has something to fight against, and you’ll see it later. Clean grout, clean tile, clean panels — that’s the foundation.
Once everything was scrubbed down and dried out, I ran a fresh bead of caulk all the way around the shower. Two reasons for that. One, it gives the whole enclosure a finished, complete look instead of leaving gaps where the panels meet. Two, and more important, it seals the thing up against water. A shower lives and dies on staying watertight, and old, cracked, shrinking caulk is how moisture gets behind your walls and starts causing real problems. New caulk all the way around takes care of that before the coating ever goes on.
Then came the masking. I taped and covered the entire room — floor, walls, anything outside the enclosure that I didn’t want touched. Acrylic enclosure reglazing throws a fine overspray once you start spraying, and that mist drifts. It’ll settle on every surface in the bathroom if you give it the chance. So I seal the room off completely first. It takes time, but it’s the difference between a clean job and one that leaves a mess behind.
With the room masked and the surface prepped, I laid down a bright white coating across the whole enclosure. That’s the moment it all comes together. The acrylic, the tile, the whole combination came out looking like one smooth, glossy, bright white surface — exactly the modern, fresh look the homeowner was after. Once his new fixtures go on, it’s going to look like a brand new shower.
The same process works on bathtubs — same deep cleaning, same prep, same sprayed finish. A stained porcelain tub, a chipped cast iron tub, a dull fiberglass tub and shower combo: we repair what’s wrong and lay a bright new finish over a properly prepped surface, in one day, backed by our warranty.
This job was in Hemet, but we handle bathtub reglazing, acrylic enclosure reglazing, and tub and shower combination refinishing all over Riverside, San Bernardino, and Orange County — including San Jacinto, Menifee, and Winchester. Whether your tub is beat up or just dated, reglazing gives you a clean, modern finish for a fraction of what a full replacement runs.
Give us a call at (310) 401-4491. We give honest estimates and we’ll tell you straight whether reglazing is the right move for your bathroom.
For more information you can check out our Blog or FAQ.
