Welcome to Adamov Reglazing, your trusted partner for bathtub reglazing and cabinet refinishing services in Southern California. We proudly serve residential and commercial clients across multiple locations, helping you revitalize your bathrooms and kitchens with cost-effective, professional solutions.
Looking for bathtub reglazing in Big Bear? Adamov Reglazing restores porcelain, cast iron, fiberglass, and acrylic tubs across Big Bear Lake, Big Bear City, and the surrounding mountain communities — ready to use in about 7 hours, backed by a 4-year warranty, with no hidden costs. Reglazing instead of replacing saves thousands of dollars and days of demolition mess.
Big Bear’s cabins and mountain homes are full of original cast iron and porcelain tubs — heavy, well-built fixtures from an era when they were made to last, and often better than anything you’d replace them with. Getting a replacement tub up the mountain and a remodel crew scheduled is expensive and slow, which makes reglazing the practical choice here. It matters for vacation rental owners too: we can turn a tired tub or shower around in one visit between bookings instead of losing a week of the season.
We handle:
Just wrapped a cast iron tub reglaze up in Big Bear, and the before-and-after on this one was honestly one of the more dramatic ones we’ve done lately. It was an old cast iron tub — heavy, solid, the kind that’s built to last decades — but the bottom had taken a real beating over the years and needed a lot of attention before it could look new again.
The first problem was staining. The drain area was discolored, and from what we could tell it had been hit with some strong cleaning chemicals at some point. That’s a more common mistake than people realize. Harsh, acidic cleaners might cut through grime in the moment, but on porcelain they can etch and stain the surface permanently, and once that damage is in there, no amount of scrubbing pulls it back out. So that’s where we started — a deep cleaning to strip off everything sitting on the surface, followed by etching the bottom to lift those chemical stains out as much as we possibly could. You won’t always get a chemically stained surface back to perfect, but proper etching pulls out a great deal of it and, just as importantly, preps the surface so the coating bonds the way it should.
But the staining was only half the story. The bottom of this tub was rough. We’re talking a lot of scratches, small chips, and porcelain that had genuinely worn out down there from years of use. A surface in that condition can’t just be sprayed over — if you lay finish on top of a rough, pitted bottom, the new coating shows every flaw underneath it, scratch for scratch. So after the cleaning and etching, we applied body filler across the whole bottom, troweling it out to fill the scratches and chips and build a smooth, even base. Then it gets sanded back flat, so what was a rough, worn-out tub bottom becomes a clean, uniform surface ready to take a finish. That filling-and-smoothing step is the real labor on a job like this, and it’s the difference between a tub that looks new and one that just looks repainted.
From there, it’s our standard process, done the right way every time. We ran fresh caulking all the way around the top of the tub, since old caulk is almost always cracked or pulling loose and it’s the right moment to handle it. We masked off the entire bathroom — walls, fixtures, floor — so overspray couldn’t settle anywhere it didn’t belong. And because cast iron tubs are often in older homes with closed-up bathrooms, we set up our commercial exhaust blower system to pull the fumes out of the house and keep the air clear during the spraying process. That ventilation step keeps the customer comfortable and the workspace safe.
With the room sealed and the air moving, we sprayed down a bright white finish, building it up in even coats. And the transformation was phenomenal. You honestly could not tell that just a couple hours earlier that same tub bottom was stained, scratched, and worn out. Bright, smooth, glossy white from end to end — looked like a brand-new tub.
That’s really the magic of reglazing a solid old cast iron tub. The tub itself is built better than most of what you’d replace it with, so it’d be a shame to tear it out. Instead we fix what’s actually wrong — the stains, the rough bottom, the worn porcelain — and refinish the surface so you keep that heavy, quality tub and it looks new again. We do the whole thing in a single day, it’s backed by our warranty, and it costs a fraction of what a replacement would run.
Every job finishes the same way: we hand over a post-care kit and our cleaning recommendations, so you know exactly how to keep the finish looking sharp. On a tub like this one, that matters double — the original damage came from harsh chemical cleaners, and the right products are what keep a new finish from going the same way. A good reglaze isn’t just about the day we finish; it’s about how it holds up years down the road.
We cover a wide stretch of Southern California — all of Orange County, plus San Bernardino and Riverside across the Inland Empire, including the mountain communities: Big Bear Lake, Big Bear City, Lake Arrowhead, Running Springs, and Crestline.
Got a tub or shower you’ve been thinking about? Call (310) 401-4491. We give honest estimates — if reglazing is the right move, we’ll tell you, and if it’s not, we’ll be straight with you about that too.
For more information you can check out our Blog or FAQ.
